Manual for Outdoor LoRaWAN Gateway - GWLRW

MicrosoftTeams-image-(124).png

Thank you very much for choosing Daviteq Wireless Sensors. We are the leading wireless sensor manufacturer in the World. We have a wide range of wireless sensors which support different connectivity like LoRaWAN, Sigfox, Sub-GHz, NB-IoT...Please find out more information at this link.

This manual is applied to the following products

Item code HW Version Firmware Version Remarks
GWLRW-9 1.0 1.0  

To use this product, please refer step by step to the below instructions.

1.  Quick Guide

Reading time: 10 minutes
Finish this part so you can understand and put the device in operation with the default configuration from the factory.

1.1 What is the GWLRW ?

GWLRW is a LoRaWAN Gateway designed for outdoor installation, used in projects such as Smart Factory, Smart Agriculture, Smart Building, Smart Residential Area, Smart City... It supports simultaneously 8 connection channels to help receive a large number of packets from surrounding LoRaWAN sensors. The connection distance to the LoRaWAN sensors is up to 10 Km (depending on the environment and sensor types). It supports common communications such as Ethernet, LTE, WiFi. LoRa frequency support 863~870 MHz / 902~928 MHz.

This LoRaWAN Gateway is widely used in applications such as reading water meters, electricity meters, gas meter, environmental monitoring, smart farms, smart factories...

1.2 What's in the package?

      The package includes:
      01 x LoraWAN Gateway
      01 x Lora Antenna
      01 x LTE Antenna
      01 x Adapter
      01 x Accessory set

      fullpackage.png

      1.3 Product Overview

      1.3.1 I/O Ports

      IO-port.png

      1.3.2 LED Functions
      LED Functions Constant Flashing Off
      Power Power On Booting /OTA OFF
      Internet Internet Available Checking Internet RFU
      Service LNS Connected RFU LNS Not Connected
      LoRa LoRa Working Initializing LoRa Not Working
      1.3.3 Reset Button
      • Reboot:
        By pressing and holding the RESET Button, the Power LED will start flashing. The “reboot” procedure will be triggered when the RESET Button is released while the Power LED light is
        flashing.
      • Restore to Default:
        By pressing and holding the RESET Button, the Power LED will start flashing. The “restore to default” procedure will be triggered when the RESET Button released after the Power LED
        light becomes constant.

      1.4 Installation 

      Startup the LoraWAN Gateway through the following steps

      Step 1: Install the antennas of the LoRaWAN Gateway

      Install the LTE antenna and the Lora antenna in the correct position. Make sure the antennas and Gateway are tightly connected.

      antenna.png

      Step 2: Insert the SIM card into the LoRaWAN Gateway

      Remove the plastic plate in the SIM socket, then insert the SIM card into the socket with correct SIM direction.

      sim.png

      Pay attention to the direction of the SIM

      Note: If the gateway use only Ethernet port to connect to Network Sever, skip step 2

      Step 3: Connect the Ethernet cable and power up the Gateway

      Connect the Ethernet cable into RJ45 port. After that, connect the power adapter provided to the Terminal Block ,then the gateway will automatically turn on after powering up.

      power-and-lan.png

      Step 4 : Close the gateway's cover, then use the hex wrench to lock the 4 screws.

      cover.jpg

       

      1.5 Mounting

      Step 1: Mount the bracket to the steel pole with a hose clamp or attach it to the wall. Then mount the gateway on the bracket.

      mounting.png

      Step 2: Secure the M4 screwmounting-1.png

      1.6  Configure the LoRaWAN Gateway

      1.6.1 GUI Access 

      Default mode of Daviteq Gateway is DHCP. Once gateway is turned on through plugging in the DC adapter, it will automatically link to available servers. Gateway’s IP address can be found from the DHCP server. Access Gateway Web UI via the DHCP IP on browser. The default username is “admin”, and the password can be found on the inside label.

      To access the GUI, follow these steps:

      Step 1: Use a computer to connect to the network that the gateway is connected. The computer can connect to that network via WiFi or Ethernet.

      Step 2: Use the IP scanning software to find the IP address of the gateway based on its Mac address that can be found on the back label.

      ip-scan.jpg

      Step 3: Enter the IP address of the gateway in the web browser to access the configuration interface.

      For example, If the IP address of the Gateway is 192.168.1.15 , you should enter exactly that information in web browser, then the GUI will be displayed.
      login.jpg

      1.6.2 WAN configuration

      The purpose of this category is to view current WAN settings. This category is further divided into three sectors: WAN Status, Wan Settings and 3G/4G LTE Log. 

      • WAN Status

      The current network status will be shown on this page.

      wan-status.jpg

      • WAN Settings

      Daviteq Gateway supports three WAN Modes: Ethernet WAN, 3G/4G LTE and Dual WAN (Ethernet+3G/4G). Default mode of Daviteq Gateway is Dual WAN.

      WAN-setting.jpg

      Note: Configure “APN” information according to mobile service provider requirements.

      1.6.3 Lora Settings

      The LoRa menu consists of the following categories: Mode Selection, Channel Scan and Log. Configure some basic fields for the gateway operation.

      • Mode selection

      At the field, choose the "Packet Forwarder" option and click the "APPLY" button to Enable the Packet Forwarder mode. After applying the setting, the "Packet Forwarder" field can be found on the left menu.

      mode.jpg

      • Packet Forwarder configuration

      Select Packet Forwarder in the left menu, then choose Gateway Info. This page is for setting up the LoRa configuration including Gateway ID, Server Address, Server Uplink Port, Server Downlink Port, Keep-Alive Interval, Statistics Display Interval, and Push Timeout.

      packet-forwarder.jpg

      Need to properly configure the Server Address, Server Uplink Port, and Server Downlink Port fields. These information depend on the Network server.

      • Radio and Channel Settings

      This page is for configuring the radio 0 and radio 1 configurations of Lora, including Central Frequency, Channel Status, and Center frequency offset. The frequencies and channels are regulated by the lora-alliance, region and the network server. Below is an example of the configuration of the frequency AS923-2.

      radio.png

      1.7 Add the LoraWAN Gateway to Network Server

      To give an example, please follow the instructions in this link to add LoraWAN gateway to The things Stack network server.

      2. Product specification 

      Please refer to the detailed specifications in this link

      3. Warranty and Support 

      For warranty terms and support procedures, please refer to this link.

      4. References

      Use-cases:

      Case studies:

      White-papers:

      END.

       


      Revision #12
      Created Mon, Mar 20, 2023 12:07 AM by Phi Hoang Tran
      Updated Fri, Mar 24, 2023 1:01 AM by Phi Hoang Tran